Test methods of plastic and plastic products, catalog, Chinese standards (6)
time:2015-03-08 22:08:11,count:0

Test methods of plastic and plastic products, catalog, Chinese standards (6)


GB/T 19277.2-2013     Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions - Method by analysis of evolved carbon dioxide - Part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test
GB/T 19279-2003     Polyethylene pipes--Resistance to slow crack growth--Cone test method
GB/T 19280-2003     Thermoplastics pipes for the conveyance of fluids--Determination of resistance to rapid crack propagation (RCP)--Small-scale steady-state test(S4 test)
GB/T 19466.1-2004     Plastics--Differential scanning calorimetry(DSC)--Part 1:General principles
GB/T 19466.2-2004     Plastics--Differential scanning calorimetry(DSC)--Part 2:Determination of glass transition temperature
GB/T 19466.3-2004     Plastics--Differential scanning calorimetry(DSC)--Part 3:Determination of temperature and enthalpy of melting and crystallization
GB/T 19466.6-2009     Plastics - Differential scanning calorimetry(DSC)- Part 6: Determination of oxidation induction time(isothermal OIT)and oxidation induction temperature(dynamic OIT)
GB/T 19467.1-2004     Plastics--Acquisition and presentation of comparable single-point data--Part 1:Moulding materials
GB/T 19467.2-2004     Plastics--Acquisition and presentation of comparable single-point data--Part 2:Long-fibre-reinforced plastics
GB/T 19603-2004     Test method for drop-proof properties of drop-proof plastic films
GB/T 19712-2005     Plastics pipes and fittings Polyethylene(PE) tapping tees Test method for impact resistance
GB/T 19806-2005     Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies
GB/T 19807-2005     Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting
GB/T 19808-2005     Plastics pipes and fittings Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
GB/T 19809-2005     Plastics pipes and fittings-Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion
GB/T 19810-2005     Polyethylene(PE)pipe and fittings-Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
GB/T 19811-2005     Plastics-Determination of the degree of disintegration of plastic materials under defined composting conditions in a pilot-scale test
GB/T 19993-2005     Thermoplastics piping systems for hot and cold water supply-Test method for the resiance of pipes and fittings mounted assemblies to thermal cycling
GB/T 20220-2006     Plastics - Film and sheeting - Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness)
GB/T 20022-2005     Plastics -- Homopolymer and Copolymer resins of vinyl chloride Determination of apparent density
GB/T 20197-2006     Define, classify, marking and degradability requirement of degradable plastic
GB/T 20417.2-2006     Plastics--Acrylonitrile-butadiene-styrene(ABS)moulding and extrusion materials--Part 2: Preparation of test specimens and determination of properties
GB/T 20467-2006     Flexible cellular polymeric materials - Moulded and extruded sponge or expanded cellular rubber products - Compressibility test on finished parts
GB/T 20672-2006     Cellular plastics, rigid - Determination of compressive creep under specified load and temperature conditions
GB/T 20673-2006     Cellular plastics - Determination of the coefficient of linear thermal expansion of rigid materials at sub-ambient temperatures
GB/T 21060-2007     Plastics - Determination of pourability
GB/T 21300-2007     Plastics pipes and fittings - Determination of opacity
GB/T 21332-2008     Rigid cellular plastics - Determination of water vapour transmission properties
GB/T 21333-2008     Cellular plastics,rigid - Test methods for self-skinned,high-density materials
GB/T 21460.2-2008     Plastics - Styrene/acrylonitrile(SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
GB/T 21461.2-2008     Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
GB/T 21843-2008     Plastics - Vinyl chloride homopolymer and copolymer resins - Particle size determination by mechanical sieving
GB/T 21988-2008     Plastics-Vinyl chloride homopolymer and copolymer resins-Sieve analysis in water
GB/T 21989-2008     Plastics - Poly(vinyl chloride)pastes - Determination of apparent viscosity using the severs rheometer
GB/T 21990-2008     Polyvinyl chloride (PVC) pastes - Determination of fineness of grind
GB/T 21991-2008     Plastics - Preparation of PVC paste for test purpose - Planetary-mixer method

Home | Surfactants | Documents | Standards | Enterprise | Essays | Links | Navigation | Copyright | Advertising | About us | Bulletin

简体中文 | 繁體中文 | English

MP: 0086 180 0222 7832;   Email: ssunliu@gmail.com

Copyright 2004-2016 SAAPedia All Rights Reserved.